In this article down the page you can locate a lot of helpful guidance with regards to Tools You Need to Install a New Bathtub .
Installing a tub isn't precisely brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is additionally a reasonably hard project. If the old tub is readily obtainable, the task can move easily; if you have to open up a wall surface to get rid of the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub as well as embeded in the brand-new one. Ensure you have certified yourself for the work and also fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is much better to take into consideration using one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This write-up will certainly aid you install a brand-new bathtub in your washroom if you have actually already purchased a new tub as well as don't require to alter the arrangement of your previous water system pipes.
Your devices and product checklist should comprise the following:
Planning for the Installment
To start with, the sustaining framework provided with the bath needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be fairly problematic due to the restricted accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wood boards are practical in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the tub up until the level checks out level.
To mount faucets, fit the bottom of the outermost adaptable tap port to the suitable supply pipe by making a compression join; then do the very same for the other faucet.
Switch on the supply of water and also examine all joints and also new pipework for leakages as well as tighten them if essential. Fill up the tub as well as also inspect the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait up until the bath tub has actually been utilized a minimum of when as this will certainly resolve it right into its final placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location between the tap and the sink. Safeguard the tap in place with the producer provided backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to break an inflexible seal, creating the water to penetrate the wall surface between the bathroom and also the tiling, bring about difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes and cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to enable the activity experienced when the tub is in use. The sealer can split fairly very early if you do not think about this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you enjoy reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Leave feedback directly below. We will be interested to listen to your thinking about this review. Hoping that you come back again later on. I beg you take a moment to promote this entry if you enjoyed reading it. I am grateful for your time. Come back soon.
Quality fix? Call!